Fresh Install [Archives] - Le forum officiel de l'Association Asterisk France

Voir la version complète : Fresh Install

alternatiq

05/06/2013, 00h46

Bonjour,

Je viens de faire une fresh install d'asterisk avec une B410P.
Asterisk 1.8.22.0 + Dahdi 2.6.2 + Libpri 1.4.14

J'ai créé un truck sur Port1 de la Carte = Span1
J'ai créé 2 users ... 8100 + 8096

J'ai un dialplan avec des regles .... et je veux sortir !!!

National _0[1-5]XXXXXXXX Span 1
International _00. Span 1
Portables _0[6-7]XXXXXXXX Span 1
Num_Spec _0[8-9]XXXXXXXX Span 1
Num_Court _XNNN Span 1

== Using SIP RTP CoS mark 5
-- Executing [0618830604@DLPN_Solares:1] Macro("SIP/8100-00000003", "trunkdial-failover-0.3,DAHDI/g1/0618830604,,span_1,,0388309774") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:1] GotoIf("SIP/8100-00000003", "0?1-fmsetcid,1") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000003", "1?1-setgbobname,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-setgbobname,1)
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:1] Set("SIP/8100-00000003", "CALLERID(name)=Solares Bauen") in new stack
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:2] Goto("SIP/8100-00000003", "s,3") in new stack
-- Goto (macro-trunkdial-failover-0.3,s,3)
-- Executing [s@macro-trunkdial-failover-0.3:3] Set("SIP/8100-00000003", "CALLERID(num)=0388309774") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:4] Set("SIP/8100-00000003", "CALLERID(all)=0388309774") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:5] GotoIf("SIP/8100-00000003", "1?1-dial,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-dial,1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:1] Dial("SIP/8100-00000003", "DAHDI/g1/0618830604") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called DAHDI/g1/0618830604
-- Span 1: Channel 0/1 got hangup, cause 3
-- Hungup 'DAHDI/i1/0618830604-3'
== Everyone is busy/congested at this time (1:0/0/1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000003", "0 > 0 ?1-CHANUNAVAIL,1:1-out,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-out,1)
-- Executing [1-out@macro-trunkdial-failover-0.3:1] Hangup("SIP/8100-00000003", "") in new stack
== Spawn extension (macro-trunkdial-failover-0.3, 1-out, 1) exited non-zero on 'SIP/8100-00000003' in macro 'trunkdial-failover-0.3'
== Spawn extension (DLPN_Solares, 0618830604, 1) exited non-zero on 'SIP/8100-00000003'

En entrée pas de soucis, mon catchall vers un groupe est OK !!!

ipbx*CLI> dahdi show channels
Chan Extension Context Language MOH Interpret Blocked State
pseudo default default In Service
1 DID_span_1 fr default In Service
2 DID_span_1 fr default In Service
ipbx*CLI>

ipbx*CLI> sip show users
Username Secret Accountcode Def.Context ACL ForcerPort
8096 DLPN_Solares No Yes
8100 DLPN_Solares No Yes
ipbx*CLI>

root@ipbx: $ cat /etc/dahdi/system.conf
# Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 5 00:44:29 2013
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" (MASTER) AMI/CCS
span=1,1,0,ccs,ami
# termtype: te
bchan=1-2
hardhdlc=3
echocanceller=mg2,1-2

# Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2" RED
span=2,2,0,ccs,ami
# termtype: te
bchan=4-5
hardhdlc=6
echocanceller=mg2,4-5

# Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3" RED
span=3,3,0,ccs,ami
# termtype: te
bchan=7-8
hardhdlc=9
echocanceller=mg2,7-8

# Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4" RED
span=4,4,0,ccs,ami
# termtype: te
bchan=10-11
hardhdlc=12
echocanceller=mg2,10-11

# Global data

loadzone = us
defaultzone = us
root@ipbx: $

J'ai l'impression que ce GUI de Digium pour asterisk fout la merde quand il parse les files ....

Donc je sors pas !!! une idée

alternatiq

05/06/2013, 08h14

Appel Entrant : OK

-- Accepting call from '9xx07xx13' to '388xx97xx' on channel 0/1, span 1
-- Executing [388xx97xx@DID_span_1:1] Goto("DAHDI/i1/954077413-2", "ringroups-custom-1,s,1") in new stack
-- Goto (ringroups-custom-1,s,1)
-- Executing [s@ringroups-custom-1:1] NoOp("DAHDI/i1/9xx07xx13-2", "Accueil") in new stack
-- Executing [s@ringroups-custom-1:2] Dial("DAHDI/i1/9xx07xx13-2", "SIP/8100,20,i") in new stack
== Using SIP RTP CoS mark 5
-- Called SIP/8100
-- SIP/8100-00000001 is ringing
-- Span 1: Channel 0/1 got hangup, cause 16
== Spawn extension (ringroups-custom-1, s, 2) exited non-zero on 'DAHDI/i1/954077413-2'
-- Hungup 'DAHDI/i1/9xx07xx13-2'

Emmeteur = 09xx07xx13
Recevant = 0388xx97xx

Pourquoi le 0 est supprimé ?

Appel Sortant : NOK

== Using SIP RTP CoS mark 5
-- Executing [06xx83xx04@DLPN_solares:1] Macro("SIP/8100-00000002", "trunkdial-failover-0.3,DAHDI/g1/06xx83xx04,,span_1,,0388xx97xx") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:1] GotoIf("SIP/8100-00000002", "0?1-fmsetcid,1") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000002", "1?1-setgbobname,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-setgbobname,1)
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:1] Set("SIP/8100-00000002", "CALLERID(name)=Solares Bauen") in new stack
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:2] Goto("SIP/8100-00000002", "s,3") in new stack
-- Goto (macro-trunkdial-failover-0.3,s,3)
-- Executing [s@macro-trunkdial-failover-0.3:3] Set("SIP/8100-00000002", "CALLERID(num)=0388xx97xx") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:4] Set("SIP/8100-00000002", "CALLERID(all)=0388xx97xx") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:5] GotoIf("SIP/8100-00000002", "1?1-dial,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-dial,1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:1] Dial("SIP/8100-00000002", "DAHDI/g1/06xx83xx04") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called DAHDI/g1/06xx83xx04
-- Span 1: Channel 0/1 got hangup, cause 3
-- Hungup 'DAHDI/i1/06xx83xx04-3'
== Everyone is busy/congested at this time (1:0/0/1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000002", "0 > 0 ?1-CHANUNAVAIL,1:1-out,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-out,1)
-- Executing [1-out@macro-trunkdial-failover-0.3:1] Hangup("SIP/8100-00000002", "") in new stack
== Spawn extension (macro-trunkdial-failover-0.3, 1-out, 1) exited non-zero on 'SIP/8100-00000002' in macro 'trunkdial-failover-0.3'
== Spawn extension (DLPN_solares, 06xx83xx04, 1) exited non-zero on 'SIP/8100-00000002'

Appelé = 06xx83xx04
Appelant = 0388xx97xx

celya

06/06/2013, 23h55

Quel est ton opérateur ?

Tu a essayer d'appeler sans le 0 devant ton numéro.

olppp

07/06/2013, 09h46

jean

07/06/2013, 13h58

appel ok : 9 chiffres sans le 0
appel ko: 10 chiffres avec le 0

cause=3: No route to destination (http://helpdesk.netcentral.co.uk/index.php?_m=knowledgebase&_a=viewarticle&kbarticleid=293)

alternatiq

12/06/2013, 16h06

Bonjour,

certainement un problème de réglage ISDN
la plupart du temps la numérotation est sur 9 chiffres, le 0 est géré par l'équipement

déjà dans /etc/dahdi/system.conf
loadzone=fr
defaultzone=fr

pour /etc/asterisk/chan_dahdi.conf ça dépend de l'opérateur

par expérience chez SFR

switchtype=euroisdn
pridialplan=dynamic
internationalprefix = 00
nationalprefix = 0

chez Completel

switchtype=euroisdn
pridialplan=unknown
internationalprefix = 00
nationalprefix = 0

la différence au niveau de pridialplan entre SFR et Completel joue sur la présentation des numéros en sortie

Bonjour,

OK avec les infos, mais pourquoi la config vi la GUI de digium ne fait pas le boulot correctement ?

Le fichier system.conf passe de :

# Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 11 16:53:24 2013
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" (MASTER)
span=1,1,0,ccs,ami
# termtype: te
bchan=1-2
hardhdlc=3
echocanceller=mg2,1-2

# Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2"
span=2,2,0,ccs,ami
# termtype: te
bchan=4-5
hardhdlc=6
echocanceller=mg2,4-5

# Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3"
span=3,3,0,ccs,ami
# termtype: te
bchan=7-8
hardhdlc=9
echocanceller=mg2,7-8

# Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4"
span=4,4,0,ccs,ami
# termtype: te
bchan=10-11
hardhdlc=12
echocanceller=mg2,10-11

# Global data

loadzone = fr
defaultzone = fr

a ceci :

span = 1,1,0,ccs,ami
span = 2,2,0,ccs,ami
bchan = 1-2,4-5
hardhdlc = 3,6
echocanceller = mg2,1-240
loadzone = fr
defaultzone = fr

et que le dahdi-channels dans /etc/asterisk ne passe pas :

; Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 12 15:27:10 2013
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" AMI/CCS
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 1-2
context = default
group = 63

; Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2" (MASTER) AMI/CCS
group=0,12
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 4-5
context = default
group = 63

; Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3" AMI/CCS RED
group=0,13
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 7-8
context = default
group = 63

; Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4" AMI/CCS RED
group=0,14
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 10-11
context = default
group = 63

à ceci :

; Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 12 15:27:10 2013
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" AMI/CCS
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 1-2
context = default
group = 63

; Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2" (MASTER) AMI/CCS
group=0,12
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 4-5
context = default
group = 63

; Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3" AMI/CCS RED
group=0,13
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 7-8
context = default
group = 63

; Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4" AMI/CCS RED
group=0,14
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 10-11
context = default
group = 63

ce qui est important, c'est que je passe de FT en bri_cpe_ptmp a du completel bri_cpe et que sans le faire à la mano ... rien se fait !!!