Fresh Install

Bonjour,

Je viens de faire une fresh install d'asterisk avec une B410P.
Asterisk 1.8.22.0 + Dahdi 2.6.2 + Libpri 1.4.14

J'ai créé un truck sur Port1 de la Carte = Span1
J'ai créé 2 users ... 8100 + 8096

J'ai un dialplan avec des regles .... et je veux sortir !!!

National _0[1-5]XXXXXXXX Span 1
International _00. Span 1
Portables _0[6-7]XXXXXXXX Span 1
Num_Spec _0[8-9]XXXXXXXX Span 1
Num_Court _XNNN Span 1

== Using SIP RTP CoS mark 5
-- Executing [0618830604@DLPN_Solares:1] Macro("SIP/8100-00000003", "trunkdial-failover-0.3,DAHDI/g1/0618830604,,span_1,,0388309774") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:1] GotoIf("SIP/8100-00000003", "0?1-fmsetcid,1") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000003", "1?1-setgbobname,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-setgbobname,1)
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:1] Set("SIP/8100-00000003", "CALLERID(name)=Solares Bauen") in new stack
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:2] Goto("SIP/8100-00000003", "s,3") in new stack
-- Goto (macro-trunkdial-failover-0.3,s,3)
-- Executing [s@macro-trunkdial-failover-0.3:3] Set("SIP/8100-00000003", "CALLERID(num)=0388309774") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:4] Set("SIP/8100-00000003", "CALLERID(all)=0388309774") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:5] GotoIf("SIP/8100-00000003", "1?1-dial,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-dial,1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:1] Dial("SIP/8100-00000003", "DAHDI/g1/0618830604") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called DAHDI/g1/0618830604
-- Span 1: Channel 0/1 got hangup, cause 3
-- Hungup 'DAHDI/i1/0618830604-3'
== Everyone is busy/congested at this time (1:0/0/1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000003", "0 > 0 ?1-CHANUNAVAIL,1:1-out,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-out,1)
-- Executing [1-out@macro-trunkdial-failover-0.3:1] Hangup("SIP/8100-00000003", "") in new stack
== Spawn extension (macro-trunkdial-failover-0.3, 1-out, 1) exited non-zero on 'SIP/8100-00000003' in macro 'trunkdial-failover-0.3'
== Spawn extension (DLPN_Solares, 0618830604, 1) exited non-zero on 'SIP/8100-00000003'

En entrée pas de soucis, mon catchall vers un groupe est OK !!!

ipbx*CLI> dahdi show channels
Chan Extension Context Language MOH Interpret Blocked State
pseudo default default In Service
1 DID_span_1 fr default In Service
2 DID_span_1 fr default In Service
ipbx*CLI>

ipbx*CLI> sip show users
Username Secret Accountcode Def.Context ACL ForcerPort
8096 DLPN_Solares No Yes
8100 DLPN_Solares No Yes
ipbx*CLI>


root@ipbx: $ cat /etc/dahdi/system.conf
# Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 5 00:44:29 2013
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" (MASTER) AMI/CCS
span=1,1,0,ccs,ami
# termtype: te
bchan=1-2
hardhdlc=3
echocanceller=mg2,1-2

# Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2" RED
span=2,2,0,ccs,ami
# termtype: te
bchan=4-5
hardhdlc=6
echocanceller=mg2,4-5

# Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3" RED
span=3,3,0,ccs,ami
# termtype: te
bchan=7-8
hardhdlc=9
echocanceller=mg2,7-8

# Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4" RED
span=4,4,0,ccs,ami
# termtype: te
bchan=10-11
hardhdlc=12
echocanceller=mg2,10-11

# Global data

loadzone = us
defaultzone = us
root@ipbx: $

J'ai l'impression que ce GUI de Digium pour asterisk fout la merde quand il parse les files ....

Donc je sors pas !!! une idée

Appel Entrant : OK

-- Accepting call from '9xx07xx13' to '388xx97xx' on channel 0/1, span 1
-- Executing [388xx97xx@DID_span_1:1] Goto("DAHDI/i1/954077413-2", "ringroups-custom-1,s,1") in new stack
-- Goto (ringroups-custom-1,s,1)
-- Executing [s@ringroups-custom-1:1] NoOp("DAHDI/i1/9xx07xx13-2", "Accueil") in new stack
-- Executing [s@ringroups-custom-1:2] Dial("DAHDI/i1/9xx07xx13-2", "SIP/8100,20,i") in new stack
== Using SIP RTP CoS mark 5
-- Called SIP/8100
-- SIP/8100-00000001 is ringing
-- Span 1: Channel 0/1 got hangup, cause 16
== Spawn extension (ringroups-custom-1, s, 2) exited non-zero on 'DAHDI/i1/954077413-2'
-- Hungup 'DAHDI/i1/9xx07xx13-2'

Emmeteur = 09xx07xx13
Recevant = 0388xx97xx

Pourquoi le 0 est supprimé ?




Appel Sortant : NOK

== Using SIP RTP CoS mark 5
-- Executing [06xx83xx04@DLPN_solares:1] Macro("SIP/8100-00000002", "trunkdial-failover-0.3,DAHDI/g1/06xx83xx04,,span_1,,0388xx97xx") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:1] GotoIf("SIP/8100-00000002", "0?1-fmsetcid,1") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000002", "1?1-setgbobname,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-setgbobname,1)
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:1] Set("SIP/8100-00000002", "CALLERID(name)=Solares Bauen") in new stack
-- Executing [1-setgbobname@macro-trunkdial-failover-0.3:2] Goto("SIP/8100-00000002", "s,3") in new stack
-- Goto (macro-trunkdial-failover-0.3,s,3)
-- Executing [s@macro-trunkdial-failover-0.3:3] Set("SIP/8100-00000002", "CALLERID(num)=0388xx97xx") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:4] Set("SIP/8100-00000002", "CALLERID(all)=0388xx97xx") in new stack
-- Executing [s@macro-trunkdial-failover-0.3:5] GotoIf("SIP/8100-00000002", "1?1-dial,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-dial,1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:1] Dial("SIP/8100-00000002", "DAHDI/g1/06xx83xx04") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called DAHDI/g1/06xx83xx04
-- Span 1: Channel 0/1 got hangup, cause 3
-- Hungup 'DAHDI/i1/06xx83xx04-3'
== Everyone is busy/congested at this time (1:0/0/1)
-- Executing [1-dial@macro-trunkdial-failover-0.3:2] GotoIf("SIP/8100-00000002", "0 > 0 ?1-CHANUNAVAIL,1:1-out,1") in new stack
-- Goto (macro-trunkdial-failover-0.3,1-out,1)
-- Executing [1-out@macro-trunkdial-failover-0.3:1] Hangup("SIP/8100-00000002", "") in new stack
== Spawn extension (macro-trunkdial-failover-0.3, 1-out, 1) exited non-zero on 'SIP/8100-00000002' in macro 'trunkdial-failover-0.3'
== Spawn extension (DLPN_solares, 06xx83xx04, 1) exited non-zero on 'SIP/8100-00000002'


Appelé = 06xx83xx04
Appelant = 0388xx97xx

Quel est ton opérateur ?

Tu a essayer d'appeler sans le 0 devant ton numéro.

Bonjour,

certainement un problème de réglage ISDN
la plupart du temps la numérotation est sur 9 chiffres, le 0 est géré par l'équipement

déjà dans /etc/dahdi/system.conf
loadzone=fr
defaultzone=fr

pour /etc/asterisk/chan_dahdi.conf ça dépend de l'opérateur

par expérience chez SFR

switchtype=euroisdn
pridialplan=dynamic
internationalprefix = 00
nationalprefix = 0

chez Completel

switchtype=euroisdn
pridialplan=unknown
internationalprefix = 00
nationalprefix = 0

la différence au niveau de pridialplan entre SFR et Completel joue sur la présentation des numéros en sortie

appel ok : 9 chiffres sans le 0
appel ko: 10 chiffres avec le 0

cause=3: No route to destination (http://helpdesk.netcentral.co.uk/ind...barticleid=293)

Citation:

---

Envoyé par olppp

Bonjour,

certainement un problème de réglage ISDN
la plupart du temps la numérotation est sur 9 chiffres, le 0 est géré par l'équipement

déjà dans /etc/dahdi/system.conf
loadzone=fr
defaultzone=fr

pour /etc/asterisk/chan_dahdi.conf ça dépend de l'opérateur

par expérience chez SFR

switchtype=euroisdn
pridialplan=dynamic
internationalprefix = 00
nationalprefix = 0

chez Completel

switchtype=euroisdn
pridialplan=unknown
internationalprefix = 00
nationalprefix = 0

la différence au niveau de pridialplan entre SFR et Completel joue sur la présentation des numéros en sortie

---

Bonjour,

OK avec les infos, mais pourquoi la config vi la GUI de digium ne fait pas le boulot correctement ?

Le fichier system.conf passe de :

# Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 11 16:53:24 2013
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" (MASTER)
span=1,1,0,ccs,ami
# termtype: te
bchan=1-2
hardhdlc=3
echocanceller=mg2,1-2

# Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2"
span=2,2,0,ccs,ami
# termtype: te
bchan=4-5
hardhdlc=6
echocanceller=mg2,4-5

# Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3"
span=3,3,0,ccs,ami
# termtype: te
bchan=7-8
hardhdlc=9
echocanceller=mg2,7-8

# Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4"
span=4,4,0,ccs,ami
# termtype: te
bchan=10-11
hardhdlc=12
echocanceller=mg2,10-11

# Global data

loadzone = fr
defaultzone = fr

a ceci :

span = 1,1,0,ccs,ami
span = 2,2,0,ccs,ami
bchan = 1-2,4-5
hardhdlc = 3,6
echocanceller = mg2,1-240
loadzone = fr
defaultzone = fr

et que le dahdi-channels dans /etc/asterisk ne passe pas :

; Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 12 15:27:10 2013
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" AMI/CCS
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 1-2
context = default
group = 63

; Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2" (MASTER) AMI/CCS
group=0,12
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 4-5
context = default
group = 63

; Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3" AMI/CCS RED
group=0,13
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 7-8
context = default
group = 63

; Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4" AMI/CCS RED
group=0,14
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe_ptmp
channel => 10-11
context = default
group = 63


à ceci :

; Autogenerated by /usr/sbin/dahdi_genconf on Wed Jun 12 15:27:10 2013
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: B4/0/1 "B4XXP (PCI) Card 0 Span 1" AMI/CCS
group=0,11
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 1-2
context = default
group = 63

; Span 2: B4/0/2 "B4XXP (PCI) Card 0 Span 2" (MASTER) AMI/CCS
group=0,12
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 4-5
context = default
group = 63

; Span 3: B4/0/3 "B4XXP (PCI) Card 0 Span 3" AMI/CCS RED
group=0,13
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 7-8
context = default
group = 63

; Span 4: B4/0/4 "B4XXP (PCI) Card 0 Span 4" AMI/CCS RED
group=0,14
context=from-pstn
switchtype = euroisdn
signalling = bri_cpe
channel => 10-11
context = default
group = 63


ce qui est important, c'est que je passe de FT en bri_cpe_ptmp a du completel bri_cpe et que sans le faire à la mano ... rien se fait !!!