Affichage des résultats 1 à 2 sur 2

Discussion: PATTON SmartNode 4970 et T2

Vue hybride

Message précédent Message précédent   Message suivant Message suivant
  1. #1
    Membre Junior
    Date d'inscription
    mars 2018
    Messages
    1
    Downloads
    0
    Uploads
    0

    PATTON SmartNode 4970 et T2

    Bonjour,
    J'ai acheté un patton SN 4970 en vue de "SIPé" mon T2 vers mon asterisk.

    Sauf que quand je branche le T2 sur le port de la PATTON, rien ne se passe au niveau des LEDS d'une part et je ne peux ni émettre ni recevoir.

    Voici ma conf :
    Code:
    #----------------------------------------------------------------#
    #                                                                                  #
    # STARFACE configuration file					    #
    # for SN4970/4E30V/UI                                                 #
    # with Firmware R6.2 2012-11-12 H323 SIP BRI              #
    #                                                                                 #
    #----------------------------------------------------------------#
    
    cli version 3.20
    no terminal ssh
    administrator administrator password password
    clock local default-offset +01:00
    dns-relay
    webserver port 80 language en
    
    system
    
      ic voice 0
        low-bitrate-codec g729
    
    system
      clock-source 1 e1t1 0 0
      clock-source 2 e1t1 0 1
      clock-source 3 e1t1 0 2
      clock-source 4 e1t1 0 3
    
    profile ppp default
    
    profile tone-set default
    
    profile voip default
      codec 1 g711alaw64k rx-length 20 tx-length 20
      codec 2 g711ulaw64k rx-length 20 tx-length 20
    
    profile voip pf_voip_starface
      codec 1 g711alaw64k rx-length 20 tx-length 20 no-silence-suppression
      dtmf-relay signaling default
      fax transmission 1 bypass g711alaw64k rx-length 20 tx-length 20
      modem transmission 1 bypass g711alaw64k rx-length 20 tx-length 20
    
    profile pstn default
    
    profile sip default
      no autonomous-transitioning
    
    profile aaa default
      method 1 local
      method 2 none
    
    context ip router
      rtp-port-range 10000 12399
    
      interface if_eth0
        ipaddress <ip patton> 255.255.254.0
        tcp adjust-mss rx mtu
        tcp adjust-mss tx mtu
    
      interface if_eth1
        ipaddress unnumbered
    
    context ip router
      route 0.0.0.0 0.0.0.0 <ip passerelle> 0
      
    context cs switch
      national-prefix 0
      international-prefix 00
    
      routing-table called-e164 rt_sip_in
        route default dest-service hg_isdn cf_sip_normalize
    
      routing-table called-e164 rt_isdn_in
        route ..T3 dest-service hg_starface
    
      mapping-table calling-name to calling-pi mt_sip_a-clir
        map default to allowed
        map anonymous to restricted
    
      mapping-table calling-e164 to calling-numbering-plan mt_sip_a-numberingplan
        map default to isdn-telephony
    
      mapping-table called-e164 to called-numbering-plan mt_sip_b-numberingplan
        map default to isdn-telephony
    
      mapping-table calling-e164 to calling-type-of-number mt_sip_a-ton
        map (.%) to international
        map 0(.%) to national
        map 00(.%) to international
        map default to unknown
    
      mapping-table calling-e164 to calling-e164 mt_sip_a-e164
        map 00(.%) to \1
        map 0(.%) to \1
        map default to ""
        map (.%) to \1
    
      mapping-table calling-e164 to calling-e164 mt_sip_a-e164-localize
        map 0049(.%) to 0\1
    
      mapping-table calling-e164 to calling-si mt_sip_a-screening
        map default to user-passed
    
      complex-function cf_sip_normalize
        execute 1 cf_sip_normalize-a
        execute 2 cf_sip_normalize-b
    
      complex-function cf_sip_normalize-a
        execute 1 mt_sip_a-e164-localize
        execute 2 mt_sip_a-clir
        execute 3 mt_sip_a-numberingplan
        execute 4 mt_sip_a-ton
        execute 5 mt_sip_a-e164
        execute 6 mt_sip_a-screening
    
      complex-function cf_sip_normalize-b
        execute 1 mt_sip_b-numberingplan
    
      interface isdn if_isdn_pri0
        route call dest-table rt_isdn_in
        no call-transfer accept
        no call-transfer emit
        address-complete-indication emit set
    
      interface isdn if_isdn_pri1
        route call dest-table rt_isdn_in
        no call-transfer accept
        no call-transfer emit
        address-complete-indication emit set
    
      interface isdn if_isdn_pri2
        route call dest-table rt_isdn_in
        no call-transfer accept
        no call-transfer emit
        address-complete-indication emit set
    
      interface isdn if_isdn_pri3
        route call dest-table rt_isdn_in
        no call-transfer accept
        no call-transfer emit
        address-complete-indication emit set
    
      interface sip if_sip_starface
        bind context sip-gateway gw_sip_starface
        route call dest-table rt_sip_in
        remote <ip du starface>
        hold-method direction-attribute sendonly
        early-disconnect
        no call-transfer accept
        no call-transfer emit
        address-complete-indication accept set
        address-translation incoming-call calling-e164 from-header
        address-translation incoming-call calling-uri from-header
        address-translation incoming-call calling-name from-header
        use profile voip pf_voip_starface
    
      service hunt-group hg_starface
        drop-cause no-circuit-channel-available
        route call 1 dest-service sv_aaa_qos.if_sip_starface
    
      service hunt-group hg_isdn
        drop-cause resources-unavailable
        drop-cause circuit-channel-not-available
        route call 1 dest-service sv_aaa_qos.if_isdn_pri0
        route call 2 dest-service sv_aaa_qos.if_isdn_pri1
    
      service aaa sv_aaa_qos
        accounting start-trigger setup
        accounting use profile aaa default
    
        port if_isdn_pri0
          route call dest-interface if_isdn_pri0
    
        port if_isdn_pri1
          route call dest-interface if_isdn_pri1
    
    	port if_isdn_pri2
          route call dest-interface if_isdn_pri2
    	  
    	port if_isdn_pri3
          route call dest-interface if_isdn_pri3
    	  
        port if_sip_starface
          route call dest-interface if_sip_starface
    
    context cs switch
      no shutdown
    
    location-service ls_starface
      match-any-domain
    
      identity-group starface
    
        call outbound
    
        call inbound
    
    context sip-gateway gw_sip_starface
    
      interface gw_sip_if_starface
        bind interface if_eth0 context router port 5060
    
    context sip-gateway gw_sip_starface
      no shutdown
    
    port ethernet 0 0
      medium auto
      encapsulation ip
      bind interface if_eth0 router
      no shutdown
    
    port ethernet 0 1
      medium auto
      encapsulation ip
      bind interface if_eth1 router
      no shutdown
    
    port e1t1 0 0
      clock auto
      encapsulation q921
    
      q921
        permanent-layer2
        protocol pp
        uni-side auto
        encapsulation q931
    
        q931
          protocol dss1
          uni-side user
          bchan-number-order ascending
          encapsulation cc-isdn
          bind interface if_isdn_pri0 switch
    
    port e1t1 0 0
      no shutdown
    
    port e1t1 0 1
      clock auto
      encapsulation q921
    
      q921
        permanent-layer2
        protocol pp
        uni-side auto
        encapsulation q931
    
        q931
          protocol dss1
          uni-side user
          bchan-number-order ascending
          encapsulation cc-isdn
          bind interface if_isdn_pri1 switch
    
    port e1t1 0 1
      no shutdown
    
    port e1t1 0 2
      clock auto
      encapsulation q921
    
      q921
        permanent-layer2
        protocol pp
        uni-side auto
        encapsulation q931
    
        q931
          protocol dss1
          uni-side user
          bchan-number-order ascending
          encapsulation cc-isdn
          bind interface if_isdn_pri2 switch
    
    port e1t1 0 2
      no shutdown
    
    port e1t1 0 3
      clock auto
      encapsulation q921
    
      q921
        permanent-layer2
        protocol pp
        uni-side auto
        encapsulation q931
    
        q931
          protocol dss1
          uni-side user
          bchan-number-order ascending
          encapsulation cc-isdn
          bind interface if_isdn_pri3 switch
    
    port e1t1 0 3
      no shutdown
    Voyez-vous une grosse erreur ?
    Je dois avouer que j'y ai déjà passer quelques heures, mais je ne trouve pas.

    Mon lien reste down :
    Code:
    0DF2FA(cfg)#show port e1t1 0 0
    E1T1 Port 0:0
    =============
    Administrative State: Up
    Port: e1
    Linecode: hdb3
    Framing: crc4
    Application: short-haul
    LBO: 0-133
    LOS Threshold: -46dB
    Encapsulation: q921
    Clock: auto
    
    Operational State: Down
    Real clock: slave
    Loss of signal: true
    Frame sync: false
    Frame errors: false
    Out of frame errors: false
    Alarms: false
    Controlled slips: false
    
    BPV: 7500
    EXZ: 148078249
    LCV: 148085749
    PCV: 0
    CS: 6111

  2. #2
    Membre Association
    Date d'inscription
    septembre 2010
    Messages
    1 236
    Downloads
    0
    Uploads
    0
    Essaye de passer en NonCRC4 et demande à ton fournisseur si le canal de la signalisation est bien le 16.
    Câble Ok je suppose ?

Règles de messages

  • Vous ne pouvez pas créer de nouvelles discussions
  • Vous ne pouvez pas envoyer des réponses
  • Vous ne pouvez pas envoyer des pièces jointes
  • Vous ne pouvez pas modifier vos messages
  •